A nearly fully opened valve allows increasing flow—hence higher production—while eliminating a bottleneck or pinch in the system is possible.
Pumpenfachingenieur GmbH

It is common for process plants to contain many centrifugal pumps. In continuous processes, the conventional method for continuously controlling a pump is to throttle a control valve. The purpose is to defend the controlled variable against disturbances by adjusting the manipulated variable. In pump systems, the manipulated variable is usually the flow of liquid. When designing a pump system, process engineers typically calculate the static and dynamic pressure drop of the pipework, fittings, in-line equipment and in-line instrumentation at a fixed design flow rate. They then add the control valve’s pressure loss, which often is derived from experience. This is traditionally a fixed value of between 0.2 and 0.5 bar. Another way is to allocate a certain percentage, for example, 25 to 50 percent of the dynamic pressure loss of the system-head curve’s to the control valve’s pressure drop.1

Schematic of a simple pump systemFigure 1. Schematic of a simple pump system (Pump P) with Control Valve RV, adjusted by a level controller in Vessel V1. Design flow rate is Q. (Graphics courtesy of Pumpenfachingenieur GmbH)
Any absolute or relative control valve pressure loss must refer to a certain opening, or travel, typically 60 to 80 percent of full travel. Instead of choosing a certain travel, a percentage of the valve sizing coefficient or rated Cv (Cv at full opening) may be fixed, for example, about 60 to 75 percent.2 Depending on a valve’s parameter, the flow rate will increase when the valve is opened to 100 percent travel. However, an operating controller will respond to disturbances by oscillating so the maximum flow rate at 100 percent travel cannot be reached in reality and constitute a limit. Nevertheless, a nearly fully opened valve allows increasing flow, hence higher production, and eliminating a bottleneck or pinch is possible. Figure 1 shows a system in which a centrifugal pump (P) moves liquid from a suction side vessel (V1) to another vessel (V2). Immediately after the pressure nozzle of the pump, a bypass line forks off; this recycles part of the liquid through a resistance device to V1. The main flow passes an actuated control valve (RV) on its path to V2. The control valve’s opening, or travel, is determined by a controller, in this case, the level controller (LC) in vessel V1. The controller could also be located somewhere else in the process, for example, a temperature controller in the bottom of a distillation column. The pipework with all of its members exerts a dynamic pressure loss; so does the control valve RV. In addition, there is a total static pressure difference that consists of the difference in pressure between V1 and V2, plus pressure from the geodetic height. A generalized example can demonstrate the influence of the control valve parameter on the maximum flow rate. Pump characteristics are described using the best efficiency point (BEP) as reference. Most radial centrifugal pumps, usually small pumps featuring a low specific speed, cover the characteristics in Figure 2. Actual characteristics are scattered over a wide range with a clear tendency toward steeper characteristics similar to Curve II with increasing specific speed.3
Field of radial centrifugal pumps’ dimensionless characteristicsFigure 2. Field of radial centrifugal pumps’ dimensionless characteristics limited by Curves I and II.
Characteristics of equal-percentage control valves of different rangeability R.Figure 3. Characteristics of equal-percentage control valves of different rangeability R.
The pump system can be characterized by three parameters. The first describes the relationship between pressure loss of the control valve and that of the system (see Equation 1).
Equation 1
The second allocates a certain dimensionless travel Ys (see Equation 2) to the pressure loss of control valve ΔpRV,S at design conditions.
Equation 2 and 3
The dynamic pressure loss at design flow rate Δpdyn,S is divided also by the sum of the dynamic pressure loss plus static pressure difference Δpstatic. For example, Δpstatic = 0 reflects a closed loop system, B = 1. Changing the travel of a control valve will change flow rate. The relationship between the capacity or flow rate versus travel follows a specific curve. Equation 4 demonstrates the equal-percentage characteristic, which is found in the majority of valves.
Equation 4
Figure 3 reflects this in dimensionless terms, for example, Cv divided by rated Cv over the travel/rated travel, with the parameter being the rangeability R = 25 and R = 50, respectively.

Influence of the System’s Parameter

A calculation of the system in Figure 1 was performed with some simplifications (for example, a negligible pressure drop on the suction side and also from the pressure side of the pump to the fork-off point of the bypass). The calculation assumed a fixed bypass flow of 10 percent of flow at BEP, and the pressure drop of the control valve at design was fixed to a travel of 70 percent. The control valve featured an ideal equal-percentage characteristic and a rangeability of 25 and 50, respectively. Calculation results are shown in Figure 4 and are based on pump characteristic Curve I. The relative maximum flow rate is plotted versus A, the relative pressure drop of the control valve at design. Parameter B constitutes the system’s relative dynamic pressure loss. The same calculation was performed based on the pump’s characteristic, as demonstrated by Curve II (see Figure 5).
Maximum flow dependent on relative pressure loss of control valveFigure 4. Maximum flow dependent on relative pressure loss of control valve, variable A, based on Curve I of Figure 2. Parameter B represents the relative dynamic pressure loss of system.
Maximum flow dependent on relative pressure loss of control valveFigure 5. Maximum flow dependent on relative pressure loss of control valve, variable A, based on Curve II of Figure 2. Parameter B represents the relative dynamic pressure loss of system.
A comparison of those figures demonstrates the great influence of the pump’s characteristic on the maximum flow rate: The flatter the pump curve, the larger the maximum flow rate at a given relative pressure drop of the control valve. Doubling the rangeability of the control valve increases the maximum flow rate to a small amount. The previous scenario may be highlighted by another example having a configuration like the system in Figure 1 and where a control valve of low rangeability (base case) is replaced by valves with higher ones. The H-Q diagram in Figure 6 contains the pump’s characteristic and the system’s pressure drop curve without the loss of the control valve.
Example of the influence of a control valve’s rangeability on maximum flow rate.Figure 6. Example of the influence of a control valve’s rangeability on maximum flow rate.
Adding the control valve’s pressure loss, which had been fixed to ΔHRV = 3 m at a dimensionless travel of YS = 70 percent, results in an operating point 1 (base case) that matches the design flow rate and a bypass of 10 m3/h. The plot in Figure 6 shows several scenarios, with duty points at various maximum flow rates due to different control valves’ rangeabilities. The maximum flow rate QS is determined by a travel of 100 percent—a totally open control valve. The pressure loss curve of the system with different rangeabilities of the control valves was calculated using the appropriate rated Cv, converting it into the frictional loss factor, which is subsequently used in the Bernoulli equation. The friction loss factor decreases with increasing rangeability; in an extreme case, it becomes more or less equivalent to that of a full bore pipe having the length of the valve. Based on the design flow rate QS, the relation Qmax/QS may be taken from Figure 6:
  • Point 1 (base case): R = 25; Qmax/QS ≈ 109 percent with linear characteristic of control valve
  • Point 2: R = 25; Qmax/QS ≈ 113 percent for equal-percentage characteristic
  • Point 3: R = 150; Qmax/QS ≈ 114 percent for equal-percentage characteristic—a straight pipe replacing the control valve resulting in Qmax/QS ≈ 115 percent
This example illustrates that a high rangeability typically does not have a great effect, but this result depends on the individual system and the parameter chosen. Additionally, at the same design pressure loss and design travel of the control valve, an equal-percentage valve characteristic allows a higher maximum flow rate because of a steeply increasing Cv. Nevertheless, whenever the travel approaches 100 percent, controllability may deteriorate because a small change of travel causes a relatively large change in flow rate.

Conclusion

Qualitatively, the steeper a pump’s characteristic falls, the smaller the maximum flow rate, and the higher the relative dynamic pressure loss of the system, the smaller the maximum flow rate. The parameter “design flow rate” and “design pressure loss and travel” of the control valve establish the reference values. As a result, increasing a specified design flow rate by 10 percent, for example, without also increasing the pressure the pump delivers does not mean that the system will necessarily achieve this flow rate. References
  1. Yu, F.C., “Easy way to estimate realistic control valve pressure drops,” pp. 45-48, Hydrocarbon Processing, August 2000
  2. Unnikrishnan, G., “Visualize pump and control valve interaction easily,” pp. 51-56, Hydrocarbon Processing, August 2007
  3. Jerdal, W.A. et al., “Dimensionless Characteristics of Pumps With Specific Speeds nq = 20…80,” pp. 546- 550, Transaction ASME, Vol. 124, June 2002
  4. Green, D.W., Perry R.H., “Perry’s Chemical Engineers’ Handbook,” 8th ed., Section 8, p. 8-83
  5. To read other Efficiency Matters articles, go here.

Issue